Proceedings of the International Conference on Research and Innovations in Mechanical Engineering: Icrime-2013 (Hardcover, 2014)

Comparative Study of Laminated Composite Beam using Narrow and Wide Beam Criterion.- Design and Analysis of Submarine Radome.- Development of Lance Clamping Device for Basic Oxygen Furnace.- Development and Performance Evaluation of Water Resistant Corrugated Board for Packaging.- Mathematical Modelling Approach for Optimization of a Rotary Hook Feeder.- Tool Path Generation for Free Form Surfaces using B-Spline Surface.- Response Surface based Modeling of Mechanical System.- Vibrations Analysis of Rotor Bearing Housings Considering Unbalancing in Two Planes.- Experimental Testing and Evaluation of a Prototype Magneto-Rheological Damper.- Drilling of Glass Fibre Reinforced Epoxy Laminates with Natural Fillers: Thrust Force Analysis.- Assessment of Strength Evaluation and Structure Stability of Building Destroyed in Fire by using Techniques of Non Destructive Testing.- Corrosion Monitoring and Service Life Prediction of Rebars in Structural Concrete: State-of-Review.- Comparing Taguchi Method and RSM for Optimizing Flank Wear and Surface Roughness during Hard Turning of AISI D3 Steel.- Fine Finishing of Metal Matrix Composite Plate with Magnetic Abrasives.- Optimization of Dry Ball Burnishing Process Using Neuro Fuzzy Interface System and Genetic Algorithm.- A Review on Advances in Wire Electrical Discharge Machining (WEDM).- Effect of Filler Wire Composition on Joining Properties of GTAW Stainless Steel 202.- Effects of Machining Parameters on Performance of Electrical Discharge Surface Grinding of AISI D2 Die Steel with Composite Tool Electrode.- Optimisation of Single Point Machining Parameters for Minimum Energy Utilisation.- Development of Bio-Medical Implant (Hip Joint) by Combining Fused Deposition Modelling and Investment Casting.- Multi Response Optimization of WEDM using Utility based Taguchi Approach.- Finishing of Micro-Channels using Abrasive Flow Machining.- An Ultrasonic Micromachining Setup for Machining of 3D Geometries.- An Experimental Investigation during Wire Electrical Discharge Machining of Al/SiC-MMC.- Optimization of Magnetic Abrasive Finishing Parameters with Response Surface Methodology.- Nano Finishing of Steel Rollers (SUS 304) using Diamond based Loosely Bonded Magnetic Abrasives.- Finishing of Aluminium Pipes using Silica Sand (River Bed) Based Loosely Bonded Magnetic Abrasives.- Compression Test Analysis of Cu Super Hybrid Composite Material.- Fabrication and Characterization of Jute Fiber Reinforced-Recycled Polyethylene Composites.- Polymer Concrete Composites (PCC) Made from Industrial Waste Materials: A Review.- Effect of Molybdenum Addition in Hard Facing Layer on Erosion Resistance Behaviour of Steel.- Tribological Properties of Different Micro Abrasives in Friction Materials.- Investigation on Process Parameter Optimization for Coating Density and Micro Hardness of Cold Sprayed Coatings.- Effect of Heat Treatment on Wear Behaviour of Hard Faced Steel.- Experimental and Characterisation of Aluminium over Mild Steel by Friction Surface Processing.- Analysis of Roughness in Turning of EN-8D Alloy Steel using Cryogenically Treated HSS Tool.- Rice Husk Reinforced Composites: A Review.- Effect of Glass Fiber and Filler Volume Fraction Variation on Mechanical Properties of GFRP Composite.- Slurry Erosion Testing of Detonation Gun Sprayed Cr3C2-25NiCr and Cr2O3 Coatings on CF8M Steel.- Sliding Wear Performance of Plasma Spray Ni-20Cr Coating on AISI 309 SS Steel.- Effect of Natural Fillers on Wear Behaviour of Glass Fiber Reinforced Epoxy Composites.- SiCp Reinforced Al-6063 MMCs: Mechanical Behaviour and Micro-structural Analysis.- Effects of Humidification on Proton and Electron Conductivity of an Activated Carbon-Nafion Composite Electrode.- Combating Wear by Surface Modification Techniques.- Reduction in Fuel Consumption and CO2 Emissions by Elimination of Steam Leak from Steam Traps.- Comparative Study of Thermal Performance of Liquid Metal and Water Flow through a Channel.- Comparison of