책 이미지
책 정보
· 분류 : 국내도서 > 대학교재/전문서적 > 공학계열 > 기계공학 > 기계설계/공작
· ISBN : 9791158138905
· 쪽수 : 208쪽
책 소개
목차
서문 (Preface)
1 일반 요구사항 (General Requirements)
1.1 범위(Scope)
1.2 승인(Approval)
1.3 정의(Definitions)
1.4 용접기호(Welding Symbols)
1.5 장비 교정(Equipment Calibration)
1.6 안전 주의사항(Safety Precautions)
1.7 측정 표준 단위(Standard Units of Measurement)
2 용접 연결 설계 (Design of Welded Connections)
2.1 사용 목적(Intended Use)
3 WPS의 사전 인증 (Prequalification of WPS)
3.1 범위(Scope)
3.2 용접 공정(Welding Processes)
3.3 모재/용접봉 조합(Base Metal/Filler Metal Combinations)
3.4 최소 예열과 층간 온도 요구사항(Minimum Preheat and Interpass Temperature Requirements)
3.5 WPS 변수의 제한(Limitation of WPS Variables)
3.6 WPS 일반 요구사항(General WPS Requirements)
3.7 홈과 필릿용접의 부분 및 완전용입 이음의 일반적인 요구사항(Common Requirements of Partial and Complete Joint Penetration Groove and Fillet Welds)
3.8 부분용입 이음 요구사항(Partial Joint Penetration Requirements)
3.9 홈 용접 완전용입 이음의 요구사항(Complete Joint Penetration Groove Weld Requirements)
4 인증 (Qualification)
4.0 범위(Scope)
Part A 일반 요구사항
4.1 일반(General)
4.2 WPS와 용접 인원 수행인증에 대한 일반 요구사항(Common Requirements for WPS and Welding Personnel Performance Qualification)
Part B 절차인증
4.3 일반(General)
4.4 두께 인증 제한 (Qualification Thickness Limitations)
4.5 자세 인증 제한 (Qualification Position Limitations)
4.6 시험 및 판정 기준의 방법(Methods of Testing and Acceptance Criteria)
4.7 용접구조물 특별시험 허용기준(Special Test Weldment Acceptance Criteria)
4.8 용접구조물 홈 시험과 판정 기준(Groove Test Weldments and Acceptance Criteria)
4.9 용접구조물 필릿시험과 판정 기준(Fillet Test Weldments and Acceptance Criteria)
4.10 용접구조물 클래딩시험과 판정 기준(Cladding Test Weldment and Acceptance Criteria)
4.11 용접구조물 표면경화 시험과 판정 기준(Hard facing Test Weldment and Acceptance Criteria)
4.12 박판 용접구조물과 허용기준(Sheet Metal Weldments and Acceptance Criteria)
4.13 용접절차 사양서 자료 (Welding Procedure Specification Data)
4.14 절차인증 변수 (Procedure Qualification Variables)
Part C 수행 인증
4.15 일반 (General)
4.16 시험 (Testing)
4.17 검사방법과 판정 기준(Examination Procedures and Acceptance Criteria)
4.18 수행 인증변수 (Performance Qualification Variables)
5 제작 (Fabrication)
5.1 범위 (Scope)
5.2 모재 (Base Metal)
5.3 용접 소모품과 용접봉 요구사항(Welding Consumables and Electrode Requirements)
5.4 WPS 변수 (WPS Variables)
5.5 예열과 층간 온도 (Preheat and Interpass Temperatures)
5.6 백킹, 가스 백킹, 인서트 (Backing, Backing Gas, or Inserts)
5.7 백킹 (Backing)
5.8 용접 환경 (Welding Environment)
5.9 설계에 부합 (Compliance with Design)
5.10 모재의 준비 (Preparation of Base Metal)
5.11 가접 (Tack Welds)
5.12 변형과 수축의 제어 (Control of Distortion and Shrinkage)
5.13 필릿용접 조립 (Fillet Weld Assembly)
5.14 플러그와 슬롯 용접 기법 (Technique for Plug and Slot Welds)
5.15 보수/수정 (Rework/Repairs)
5.16 피닝(Peening)
5.17 코킹(Caulking)
5.18 아크 스트라이크(Arc Strikes)
5.19 용접 청결(Weld Cleaning)
6 검사(Inspection)
Part A 일반 요구사항
6.1 일반 (General)
6.2 용접절차 사양서와 장비의 검사(Inspection of Welding Procedure Specification and Equipment)
6.3 (자동)용접사와 가접사 인증의 검사(Inspection of Welder, Welding Operator, and Tack Welder Qualifications)
6.4 작업과 기록의 검사 (Inspection of Work and Records)
6.5 계약자의 의무 (Obligations of the Contractor)
6.6 비파괴 검사 (Nondestructive Testing)
Part B 방사선검사
6.7 일반 (General)
6.8 검사의 정도 (Extent of Testing)
6.9 방사선 절차 (Radiographic Procedures)
6.10 용접의 허용(Acceptability of Welds)
6.11 시험, 보고서 및 방사선 사진의 처분(Examination, Report, and Disposition of Radiographs)
Part C 허용기준
6.12 일반(General)
7 스터드 용접(Stud Welding)
7.1 범위(Scope)
7.2 일솜씨(Workmanship)
7.3 기법(Technique)
7.4 스터드 허용 인증 요구사항(Stud Application Qualification Requirements)
7.5 생산 제어(Production Control)
부록 APPENDICES
부록 A 4장에 따라 인증 부여가 필요한 코드 승인 모재와 용접봉
(Code Approved Base Metals and Filler Metals Requiring Qualification per Section 4)
부록 B 장갑판의 용접(Appendix B Welding of Armor Steel)
/ B1 소개(INTRODUCTION)
/ B2 참조문서 (REFERENCED DOCUMENTS)
/ B3 요구사항(REQUIREMENTS)
부록 C 양식 (Forms)
부록 D 삽화 - 스터드 용접 위치, 용접 시험 견본 및 시험 설비
/ D1 표준 스터드 시험 용접부 위치(Standard Stud Test Weldment Positions)
/ D2 형틀 굽힘 시편(Guided Bend Specimens)
/ D3 인장 시편(Tension Specimens)
/ D4 클래딩 및 표면경화 시편(Cladding and Hardfacing Specimens)
/ D5 시험 치구(Test Fixtures)
부록 E 사전 인증된 이음 준비 및 이음 세부사항(Prequalified Joint Preparations and Joint Details)